The line is generally located at the lower right edge of the back of the refrigerator. Be prepared for a small amount of water leakage as you remove the valve—this is just the standing water in the water pipe, and it can easily be sponged up. This answer will not be popular with those making their living as plumbers. I'm not a self install person, installing this by myself or with a friend is out of the question. Another possible problem is that plastic is not a very strong product and cuts quite easily.
When we first got an ice maker I used a saddle valve. Turn the nut onto the threads by hand and then tighten with an adjustable wrench. Does a nut like this need a plastic sleeve? Turn the cold water on the supply line clockwise to close it. If the line is just being replaced, unscrew the brass nut on the valve for the old icemaker line under the sink, and remove the line. Still have questions about your Kenmore refrigerator water line repair? My Dad is somewhat of a handyman and wants to fix the problem. Harsch received her Certified Nurses Assistant license in 2004.
Flex water supply tubes are available in either a tough plastic nylon mesh or braided steel. Try tapping the floor to find the hollow sound between the floor joists for a good place to drill a hole. You should hear the water starting to go through the water line. You will also need a longer flex water supply tube to run from the water pipe to the refrigerator. When hooking up a water line to a fridge ice maker or a door water supply, you want to use the correct materials to ensure the water flows well and everything is hooked up correctly with minimal chance of leaks.
Make sure to install an in-line filter for the ice maker to avoid problems with the refrigerator. Replacing water supply lines is easy if you have the proper tools for the job. Installing Water Lines for Ice Makers Many refrigerators have ice makers built into them. Avoid the saddle valves at all cost. Tighten the bolts until they are snug and you can not wiggle the saddle at all. To hook up a refrigerator ice maker, you will need to connect a line of plastic or copper tubing to a cold water line to carry water to the refrigerator. In most cases, the water line can be run from a kitchen faucet water supply line through the kitchen cabinets and over to the refrigerator.
Once the tape is on the threads, connect the water line to the threaded section. It can be very inconvenient to move a refrigerator to get at a water line that has failed, so buy the best-quality water supply tube you can. Install one end of the line on the refrigerator by threading the line through the nut, adding one of the brass ferrules to the line, and screwing the nut in place on the refrigerator valve. Tape the end of the tubing and push enough tubing through the hole to make a couple of large loops. It is also the easiest to work worth. The stainless steel braiding helps to keep it from bursting as it weakens with age. Step 2 — Remove the old Line Put a drip pan in place to catch any water that leaks.
Step 7 — Tighten Any Connections Ensure that no connections are leaking, and tighten any that are. It might cost you a few dollars more, but it will last longer and like I said very easy to work with. Usually, this will be at some other existing water hookup point, like the water supply lines connected to your sink faucet or dishwasher. Step 3 — Connect the Water Line to the Refrigerator Next, wrap the threads on the water-line connector that is on the back of the fridge with to lubricate the threads. Even if you are hiring a plumber, you should be aware of the different options available and what they mean to you. Using an adjustable wrench, remove the old line from valve. If the line is an entirely new one where a line has never been installed before , a valve will have to be installed on the cold water line under the sink.
We even made a video for you about how it all goes together without the folks at Kenmore even asking us to. Turn on the saddle-tee valve and check for leaks. These lines will eventually corrode, generally at the fittings, which can cause damage to the cabinet and produce mold. Be sure to put a gasket seal between the valve and the T-fitting. Step 3 — Attach the Fittings There are different styles of fittings that simply attach to the existing copper supply line. You'll want to use water lines that are already in place if possible, rather than attempting to install new pipes. However, if your supply pipe is galvanized steel, then you will have to shut off the water and drill a hole for the valve.
The only problem I see with using copper is that it can kink easily. The valve is sold in pieces that bolt together to form a clamping device that straddles a water line like a saddle on a horse. This line could be one from the basement, the kitchen sink, or elsewhere. What is a better line, plastic, stainless steel or copper? Some have reported noticing a bad taste in their fridge water and ice. Wrap the threads with pipe-thread tape and tighten the male fitting into the female threads.